okay guys this is my current setup as you can see this is a green screen there’s a monitor and that’s my camera where i mount it and if you see there’s a light and these are the table which i used to use for unboxing this table is going to go out now so that what we’ll be doing is we’ll be figuring out how to move that table here because i’ve got a new table which i’m going to set up and we’ll be using this big ass tripod over there so that there’ll be a better clarity in the picture which i was losing for some time this i’m just going to keep this as it is as there is no problem with it it is set properly so only this side is going to change so once i go ahead and change this table out i will move that table here and put a new table there where we will have some distance between me and the table as well as the tripod together this thing this uh five camera setup like you can see one over here one i have just removed it two three is over there four is over there and fifth camera is the dslr so let’s check how we can utilize this and if we can eliminate this light and put it somewhere here or something to make it better
okay guys you had gone ahead and seen the old table and the old design and everything now this is the new uh table which i have set up over there and you can see like the camera will be kept there and there is the light and that’s the overhead camera and there’s another side camera over there and on this table there’s a right hand side camera over here there’s a light over here there’s a ring light and an umbrella just for the design and my system is kept here with the speaker and there’s a mic in this table and as well as in that table and you do have a keyboard here and you have a headphone stand but there are no wires down there and the same thing if you see over here they have eight two two or three wires which are just these wires which are visible above and the mic wire and this is the led strip which you can see and below there no wires seen at all everything is under the sleeve which i showed you in my live other day when i did a live telecast so everything is covered in the junction box is in that and nothing looks out of the place and there are no wires going down this is the ups where all the wires are connected to and that is connected with junction box where the internet and the junction box are connected to the wall behind here
and that’s the green screen you can see
and now i’m going to show you how the cable is managed below the table just give me so if you see below the table you’ll be able to see there’s a sleeve over here by which the wire is connected to the cpu and the wires are covered over here and if you see over here is the rack over here by which the wires are going through
i’ll try to get a better view that and over here there is two three wires hanging and this is junction box stuck onto the table
and there are no wires down i’m actually lying down over here and no wires and if you see to the right hand side over here there’s another sleeve which is managing the wires and nothing is out of the place over here and all the wires are connected behind this but there’s just one wire which is going from down and that is the main hdmi wire and the power wire if you see this here big fat wire is the hdmi wire which is going through to the capture card apart from that there are no other wires now let me show you from the other side of the table also how it looks so the only things which are supposed to be kept is a speaker bluetooth speaker there’ll be another plant which will be coming over here there’s a usb over here which is giving connection to this camera that’s the overhead camera as well as the side camera and there’s another usb over here and here just for connection everything is jotted with the table with just the normal clips wire clips and the wire is connected with the light wire will be connected below the desk uh when to the junction box and if you see this wire this will be connected to the camera when the camera is fit and this wire will be connected as an hdmi to the camera so they are just kept as a side wire so here nothing else is out of space over here and there’s just some junk which i have to take off and by this i’ll be controlling all my cameras if you can see cam 1 cam 2 cam 3 cam 4 cam 5 and all the cameras i can record i can pause and some other effects are there in that even the countdown display and the virtual cam can be accessed by this i have just made it myself and here is the speaker the wire you can see over there the wire is hanging down i just have to place it over there but it will be high because we do need that much length in order to sit down and do a live stream or anything and this is the headphone which i’ll be using not the black one and on this type side of the table the only thing you can see is a normal uh
mauna mike and same as this mic and you just see a keyboard and speakers and they have the usb which is going down to the cpu so i’ve totally used one two two usb as main usb that’s it and the third one i’m not even using it now i’m just keeping it for emergency purposes because of this the day in the slots and there are no extra wires hanging out everything is covered by the sleeves everywhere and below the table there are no wires which you can see apart from this wire which i’ll be taking off later and below this table also you’re not able to see any wires because everything is packed in a sleeve and below this table i had showed you how the wires are going through so it’s a clean setup the only thing is the light has to be set up like this and if you see over here there’s umbrella stand as i showed you and below that is the normal ring light which is giving me light from the right and that is giving me light from the left and here you have the fingers camera for the right and this camera also has a fingers cam and that’s a zebronics camera as you had seen earlier how my setup was looking this setup is a little bit different than that but it’s kind of modernish setup with minimum dirt or anything around and even the scene angles are better than the previous few videos which i was making because only my face was coming very close that’s why i got that table to make the face look a little bit proper but you can even see a little bit of till my torso and the face doesn’t look like a gent face on the camera and we do have a three-point lighting as i showed you that’s the one light second light and the third light is this and i do have a small fan there for my ad because while shooting we cannot switch on the top fan or anything like that so it’s as simple as that
i hope you enjoyed this video regarding the normal setup we’ll be cleaning and polishing this more when i do my next live i’ll be showing you how the studio looks that time also and i’ll just tell you the cost of all these things the sleep cost me around just 500 bucks in total i had cut and place it in various places the box cost me about 500 bucks i just got some 3m tape also that cost about 200 bucks finally this rgb is coming for two or three hundred bucks that’s it
and that the rack which i showed you below the table the black racket just for what 445 or something rupees that’s it and normal usb hub squad charge only three to 400 bucks which you can buy this i have three point one air hubs you and you can go ahead and get that and that’s it it’s for cable management i didn’t use much more than that 100 200 rupees stuff finally max for all this the wrapper cable manager the normal strap hold or anything even if you have like this type of strap holes you can get for about 200 bucks seven pieces or something like that so you don’t need to get actually expensive stuff for this you can do it by cheap stuff also thanks for watching and if you do like videos like this please do like and subscribe for the channel and until next time this camera and you’re watching kamaltechvlog and you have a wonderful day
you